- Flirc harmony delay settings how to#
- Flirc harmony delay settings full#
- Flirc harmony delay settings software#
- Flirc harmony delay settings Pc#
So, I assigned the "AspectRatio" function to my remote's Power button in MyHarmony (since I don't need the AspectRatio function), then plugged in the FLIRC and opened up the FLIRC software, setting it to "Full Keyboard".
Flirc harmony delay settings Pc#
Just don't leave the button "unassigned" in MyHarmony, or it won't send any signal to the FLIRC when you're programming it.įor example, MyHarmony's "Flirc Kodi" profile doesn't have a function to wake the PC from sleep.
Flirc harmony delay settings software#
But if there are any functions missing, just assign a random function to a button in MyHarmony, then use the FLIRC software to "learn" that button on your remote. If you're using the FLIRC, you can map your media center's functions in MyHarmony to the buttons on your remote, and most should work without any issue. We recommend the FLIRC, though any generic USB receiver will probably work. Plug your receiver into your media center and make sure it's within view of your sitting position, so you can point your remote in its general direction.įrom there, you can map the buttons on your remote just like any other device in MyHarmony. You just need to know a few simple things.įirst, you'll need a USB infrared receiver for your media PC.
Flirc harmony delay settings how to#
How to Control Your PC with Infrared (Available on All Harmony Remotes)Ĭontrolling your PC with infrared isn't that different from setting up your Harmony remote with any other device. The closer you follow these instructions to the letter, and in the proper order, the less chance you have of running into a problem. While Logitech makes some great hardware, their software is not very good, and things can go wonky and get confusing very easily (especially when it comes to remotes with the Harmony Hub). NOTE: If you can, try to follow these instructions as closely as possible. Related: How to Control Your Entire Home Theater with a Logitech Harmony Remote If you haven't, check out our guide to getting started with Harmony first. It's a ridiculously complicated procedure, which I'm convinced is due to the Harmony or blaster as Flirc is now running fine.This guide assumes you've already become somewhat familiar with your remote and the MyHarmony software, and that you've set it up with your other devices. Setting the Inter Key Delay in the Flirc software to 2 or 3 made navigation run smoothly.
Flirc harmony delay settings full#
Using the full keyboard in Flirc, I programmed the buttons with the OPPO remote and I then proceeded to teach the keypresses of the OPPO to the Harmony using the Harmony software. Yet another remote (OPPO bluray) proved the solution. I also assigned the particular blaster to the activity in the Harmony software, didn't work either and even tried it with the cupboard open. As the Flirc is built into the case, it was too much of a hassle to try it with another PC. I tried noise cancellation on and off, a different profile in the Harmony software (media center PC) and other remotes (MCE, TV) with no success. However, in the command line (flirc_utils keys) all key presses had different codes. pause was space three times and P the fourth). I tried recording the second (and third and fourth) presses in the Flirc software, but that didn't work as the signals got mixed up (e.g.
It then turned out that the Harmony sent multiple (and I mean up to four!) different signals for each key. Out of the box the Flirc software didn't respond to the Harmony key presses so I had to record the keys. Flirc/Kodi profile in the Harmony softwareįirst, I checked the mapping of the Harmony keys in the Harmony software (they keys were based on Flirc Media Player). Maybe it can save someone from countless hours of fiddling, which is what I had to do. Just wanted to share my problems getting Flirc to work with a Harmony Elite and hub/blasters.
0 kommentar(er)
